Thinkscan Plus S2 as the Highest-level FULL OBD II Diagnostic Device For DIY users supported include Airbag /ABS/ECM System. Free Use Reset Service function (currently 28 kinds, you can choose 2 reset for free).Free for 3 system diagnostic + 10 OBD2 function, but reset function only can choose. Why You Need THINKSCAN Plus S2? Are you troubled by the renewal of model software and functions? THINKSCAN Plus S2 Support to 3 Systems (ECMABS/SRS) and you could choose 2 Reset services lifetime free. Thinkscan Plus S2 Support to diagnostic ECM/ABS/SRS system errors, and delete the error code.
Thinkscan Plus S2 supports to do Full obd 2 function, including Read/Clear codes, data stream, I/M readiness, O2 sensor, DTC look up and more... Thinkscan Plus S2 can do 2 reset revices functions like you choose. You can do screen shortcuts via I/M key with Thinkscan Plus S2 devices, easy and fast.
Thinkscan Plus S2 Support to printe Diagnostic Report data, checking errors. Thinkscan Plus S2 software update free lifetime. Support 3 System Free Diagnostic.
This car obd2 scanner is capable of reading and clearing trouble codes of ECM/ABS/SRS/ Engine. Free for Engine system Diagnostic. You can diagnose the engine system via ecu obd2 port, support all 10 OBDII test modes, such as live data, O2 sensor test, component test and more;read and clear the engine error codes, find out the exactly problem, repair it, and turn off the MIL engine light. Free for ABS system Diagnostic.
Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to retrieve ABS codes to tell you where the problem is, and this is what this scanner does for you. Free for SRS system Diagnostic. Safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this diagnostic device can detect every electronic parameter to check its health status.Free 2 Opition Maintenance Service. You Can Choose 2 Reset Service as Free from 28 Maintenance Service. The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle. To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle. This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done. When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. Lf the ABS computer, ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS. Lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. Lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.
The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car. After gear learning is successful, the MIL turns off.After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC'gear not learned is present, gear learning must be performed. To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel, ECu, BCM, or remote control battery is replaced, anti-theft key matching must be performed. Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.
After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL. Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, andtire is replaced for the car with tire pressure monitoring function. This function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.
This feature is used to initialize the adaptive headlamp system. According to the ambient light intensity, theadaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture. This function can complete the gearbox self-learning to improve gear shifting quality.
When the gearbox isdisassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impactproblem. In this case, this function needs to be done so that the gearbox can automatically compensateaccording to the driving conditions so as to achieve more comfortable and better shift quality. This function can set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc.
This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced. A ODo reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage. BUsually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODo reset after maintenance. This function resets the airbag data to clear the airbag collision fault indicator.When the vehicle collidesand the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicatorlights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable, it is required that all new accessories must be replaced, but after performing this function, the data of theairbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and theairbag computer can continue to use. Ln order to reduce power consumption, the following functions may be disabled, including limiting thevehicle speed, not waking up the door opening network, and disabling the remote control key, etc.
At thistime, the transport mode needs to be deactivated to restore the vehicle to normal. This function is applied to set or learn Air/Fuel ratio parameters.This function is used to open or close the automatic start-stop function via setting the hidden function inECU(provided that the vehicle has a hidden function and supported by hardware). NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. Lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalyticconverter learned value stored in the engine ECu. AdBlue Reset (Diesel Engine Exhaust Gas Filter). After the diesel exhaust treatment fluid (car urea) is replaced or flled up, urea reset operation is required.
This function is applied to match the seats with memory function that are replaced and repaired. Use this function to activate the electronic water pump before venting the cooling system. This function is used to set the size parameters of the modified or replaced tire. This feature is designed to perform door window matching to recover ECU initial memory, and recover theautomatic ascending and descending function of power window.This function is used to change the system language of the vehicle central control panel. Show the detailed description of the Diagnostic Trouble Code (DTCs). Turns off Check Engine Light (MIL), clears codes and resets monitors. Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing. Show the information of continuous data stream from a vehicle in live graphic (waveform) display. Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs. Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle's on-board computer.
Retrieves and displays test results for emission-related powertrain components and systems. Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc. Certain vehicle components can be actuated by commands sent from the scanner to test their operability. English, French, German, Spanish, Russian, Italian, Portuguese, Japanese.Support 93+ Worldwide Vehicle Coverage. For AUDI, For BENZ, For BMW, For CHRYSLER, For CITROEN, For DACIA, For DAEWOO, For FIAT, For GM, For HOLDEN, For HONDA, For HYUNDAI, For JAGUAR, For JPISUZU, For KIA, For LANDROVER, For MAHINDRA, For MARUTI, For MAZDA, For MINI, For MITSUBISHI, For NISSAN, For OPEL, For PEUGEOT, For PORSCHE, For RENAULT, For SAAB, For SEAT, For SKODA, For SMART, For SPRINTER, For SUBARU, For SUZUKI, For TATA, For TOYOTA, For USAFORD, For VOLVO, For VW...
Please contact customer service for specific details. How to Register/Update Thinkscan Plus S02. 1Thinkcar Thinkscan Plus S02 Host.
1Diagnostic dongle 1Charging cable 1power adapter. USA, UK, HongKong, Australia, Russian, Germany. Please return the item within. After receiving if you are not happy with your purchasing.3 Year free repair for the devices. If the item has been used, we have the right to decline your claim.
We are specialized dealer of On-Board Car Diagnostic tools and automotive electronics. For more than 10 years. We are authorized first class distributor of Launch, Foxwell, Autek, Ancel, Innova, Autophix, Thinkcar, Kzyee brands.And more brands will be show in our store in near future. We have office and warehouse in US and. We promise to help you solve it asap, and make you feel satisfactory absolutely. M-F: 9:30AM - 18:00PM BST (Beijing Standard Time). After you received our package you are satisfied with it.
We will do the same as soon as we can too. This item is in the category "eBay Motors\Automotive Tools & Supplies\Diagnostic Service Tools\Code Readers & Scanners". The seller is "super-diag" and is located in this country: US. This item can be shipped to United States.